75 lines
2.2 KiB
Plaintext
75 lines
2.2 KiB
Plaintext
**********************
|
|
NXP i.MX 93 FRDM board
|
|
**********************
|
|
|
|
This file documents the Buildroot support for the i.MX 93 FRDM
|
|
(Freedom) board. For more information on this board, see [1].
|
|
|
|
|
|
Build
|
|
=====
|
|
|
|
First, configure Buildroot for the i.MX 93 FRDM board:
|
|
|
|
make freescale_imx93frdm_defconfig
|
|
|
|
Build all components:
|
|
|
|
make
|
|
|
|
When this command completes, the generated image containing everything
|
|
to boot from the SD card is located in "output/images/sdcard.img".
|
|
|
|
|
|
Create a bootable SD card
|
|
=========================
|
|
|
|
To determine the device associated to the SD card have a look in the
|
|
/proc/partitions file:
|
|
|
|
cat /proc/partitions
|
|
|
|
Buildroot prepares a bootable "sdcard.img" image in the output/images/
|
|
directory, ready to be dumped on a SD card. Launch the following
|
|
command as root:
|
|
|
|
dd if=output/images/sdcard.img of=/dev/<your-sd-device>
|
|
|
|
*** WARNING! This will destroy all the card content. Use with care! ***
|
|
|
|
For details about the medium image layout, see the definition in
|
|
board/freescale/common/imx/genimage.cfg.template_imx9.
|
|
|
|
|
|
Boot the i.MX 93 FRDM board
|
|
===========================
|
|
|
|
To boot your newly created system (refer to the i.MX 93 FRDM
|
|
Documentation [2] for guidance):
|
|
- insert the SD card in the SD slot (P13) of the board;
|
|
- Configure the SW1 boot switches as follows:
|
|
SW1: 1100 SW1[1-4] ("USDHC2 4-bit SD3.0" Boot Mode)
|
|
- connect a USB Type-C cable into the P16 Debug USB Port and connect
|
|
using a terminal emulator at 115200 bps, 8n1;
|
|
- power on the board by connecting a USB Type-C cable into the P1
|
|
Power USB Port.
|
|
|
|
Note 1: the board boot switches default configuration is:
|
|
SW1: 0100 SW1[1-4] ("USDHC1 8-bit eMMC 5.1" Boot Mode)
|
|
and the board is also pre-flashed with a reference Linux demo
|
|
image. It is important to change the boot config switches to make
|
|
sure the system will boot on the SD Card.
|
|
|
|
Note 2: the debug USB connector presents 2 UARTs (for example
|
|
/dev/ttyACM[0-1]), the Cortex-A55 UART should be the 1st one (in the
|
|
previous example, /dev/ttyACM0). Refer to the documentation [2] for
|
|
more details.
|
|
|
|
Enjoy!
|
|
|
|
|
|
References
|
|
==========
|
|
[1] https://www.nxp.com/FRDM-IMX93
|
|
[2] https://www.nxp.com/document/guide/getting-started-with-frdm-imx93:GS-FRDM-IMX93
|